Adcom GTP-860II Bedienungsanleitung PDF herunterladen (Seite 5)

| ADCOM GTP-860 II Owner’s Manual4

5ADCOM GTP-860 II Owner’s Manual |

Congratulations on your decision to

purchase the GTP-860II 7.1 tuner/

preamplifier. Multichannel audio and

home theater are better than ever.

Your new ADCOM component was

designed to deliver all the impact

of your favorite action flick and the

subtle harmonic texture that makes

high resolution audio amazing.

Audition the GTP-860II paired with

an ADCOM power amp and DVD player

and you will experience what high

performance is all about. To realize

the full potential of your GTP-860II,

and before making any connections

to it, please read these operating and

installation instructions thoroughly.

Key Features

• Dolby Digital and DTS decoding

• ADCOM 7.1m

• Component video switching

• 24 bit/192kHz DACs

• RDS tuner

• External 5.1 input

• Torriodial power transformer

Unpacking the GTP-860II

Before your new ADCOM preampli-

fier left our factory, it was carefully

inspected for physical imperfections

and tested for all electrical parameters

as a routine part of ADCOM’s system-

atic quality control. This, along with

full operational and mechanical test-

ing, should ensure a product flawless

in both appearance and performance.

After you have unpacked the GTP-

860II, inspect it for physical damage.

Save the shipping carton and all pack-

ing material as they are intended to

reduce the possibility of transporta-

tion damage should the preamplifier

ever need to be shipped again. In the

unlikely event damage has occurred,

notify your dealer immediately and

request the name of the carrier so a

written claim to cover shipping dam-

ages can be initiated. The right to a

claim against a public carrier can be

forfeited if the carrier is not notified

promptly in writing and if the shipping

carton and packing materials are not

available for inspection by the carrier.

Save all packing materials until the

claim has been settled.

Placing the GTP-860II

Although the GTP-860II does not

generate much heat, it is good prac-

tice to ensure the preamplifier’s

long-term, trouble-free operation to

provide adequate ventilation for the

unit. Therefore, the GTP-860II should

be kept away from external sources

of heat such as radiators and hot-air

ducts.

We recommend that you exercise care

when placing components on top of

the GTP-860II. If you are placing a

heat producing component (such as

an amplifier) on top of or below the

GTP-860II, it is recommended that you

allow at least three (3) inches vertical

spacing for proper airflow.

We also recommend that you leave five

(5) inches of space behind the unit for

additional airflow and to allow space

for interconnects to hang freely.

If you observe these recommendations,

the GTP-860II will perform reliably

in any reasonable environment. You

should also pay attention to such nor-

mal considerations as protection from

excessive dust and moisture.

The optimal performance of your new

GTP-860II will ultimately depend on

the care with which you make the con-

nections between the amplifier, pream-

plifier and loudspeakers. All input and

output signal connections should be

made only with high quality, low-loss,

low capacitance cables. For recom-

mendations of the type and quality of

interconnections that are best for your

applications, consult with your ADCOM

dealer.

Safety Information

There are no user serviceable parts

inside. Refer all servicing to qualied

service personnel.

The unit must be connected to a power

supply only of the type and voltage

specied on the rear panel. Connect

the component to the power outlet only

with the supplied power supply cable or

an exact equivalent. Do not modify the

supplied cable. Do not defeat grounding

and/or polarization provisions. The

cable should be connected to a 3-pin

polarized wall outlet, matching the

wide blade of the plug to the wide slot

of the receptacle. Do not use extension

cords. Do not route the power cord

where it will be crushed, pinched,

bent, exposed to heat, or damaged in

any way. Pay particular attention to

the power cord at the plug and where

it exits the back of the unit. The power

cord should be unplugged from the wall

outlet if the unit is to be left unused

for a long period of time. Immediately

stop using the component and have

it inspected and/or serviced by a

qualied service agency if:

• the power supply cord or plug has

been damaged;

• objects have fallen or liquid has

been spilled into the unit;

• the unit has been exposed to rain;

• the unit shows signs of improper

operation; or

• the unit has been dropped or

damaged in any way.

clearance

1 2 3 4 5 6 7 8 9 10 ... 31 32

Kommentare zu diesen Handbüchern

Keine Kommentare

Adcom GTP-860II Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Empfänger und Verstärker Adcom GTP-860II

Verwandte Produkte und Handbücher für Fotozubehör Nikon WP-CP5 Coolpix S1-S3