Adcom GTP-860II Bedienungsanleitung PDF herunterladen (Seite 16)

| ADCOM GTP-860 II Owner’s Manual16

17ADCOM GTP-860 II Owner’s Manual |

explosions might wake sleeping family

members. Simply turning the volume

control down would probably make a

whisper in the next scene inaudible.

The d. range button solves this dilem-

ma by progressively lowering the

volume of loud peaks while increasing

the level of softer sounds.

[

] Volume Up/Down

In all modes, these buttons change

the master volume setting of the

GTP-860II. In all modes except main,

they can be reprogrammed with new

commands. The Volume control does

not affect recordings made using the

Tape and Video, or Tape, Video 3 and

Video 4 outputs but will affect the

signal going to the Preamp output.

[

] Mode Button

In main mode, this is pre programmed

to cycle through the surround modes

of the GTP-860II. Pressing repeatedly

will cycle through Pro Logic, Hall,

and Stereo, when available. Refer to

the Surround Mode description [8] for

more information.

[

] Play Button

In CD mode, it is pre programmed for

play with an ADCOM CD player.

[

] Pause Button

In CD mode, it is pre programmed to

pause an ADCOM CD player.

[

] Stop Button

In CD mode, it is pre programmed to

stop an ADCOM CD player.

[

] Arrow Buttons

The arrow buttons allow navigation

throughout the GTP-860II OSD (On

Screen Display) menus (as well as

the menus of other devices, once the

commands are learned). Please refer

to section 3.1 for further explanations

on the OSD.

Left arrow: In main mode, this is pre

programmed to step through the vari-

ous choices you might wish to select

while a menu item is highlighted.

In CD mode, it is pre programmed for

audible reverse scan with an ADCOM

CD player.

Up arrow/Setup: In main mode, this

is pre programmed to enter the OSD

menu system, as well as scroll up to

the next choice on a menu screen.

Right arrow: In main mode, this is

pre programmed to step through

the various choices you might wish

to select while a menu item is high-

lighted.

In CD mode, it is pre programmed for

audible forward scan with an ADCOM

CD player.

Down arrow: In main mode, this is

pre programmed to scroll down to the

next choice on a menu screen.

[

] Select Button

In main mode, this is pre programmed

to enter a selection chosen via the

menu system.

[

] Direct Access Keys

(buttons “1” through “10,” and

“+10”): In CD mode, buttons are pre

programmed as track access com-

mands for the ADCOM CD player.

[

] Test Button

Pressing the test button engages the

test signal generator. The test signal

cycles through the activated channel-

sautomatically with 3-second intervals

from Front Left, Center, Front Right,

Rear Right, Back Right, Back Left,

Rear Left, to Subwoofer in continuous

cycles. Press the test button again

to turn of the test signal. You can

make adjustments to channel balance

with the test tone generator using the

Channel Test section of the On Screen

Display setup menus.

[

] Bal (balance) Button

In main mode, this button is pre pro-

grammed to initiate balance check

procedure. Even when the GTP-860II

is correctly set-up, it may sometimes

be desirable to make minor adjust-

ments to suit the material you are

listening to. Pressing the bal button

allows for direct adjustment of all

active channels. Use the up and down

arrow buttons to select the channel

you wish to adjust and the left and

right arrows to modify the level. Both

the front panel display and the OSD

show the current status of adjust-

ments. Press the Bal button a second

time to exit this function, the new

levels will automatically be saved.

[

] Backs Button

In all modes, this button is pre pro-

grammed to toggle on and off the

Surround Back speakers.

[

] Repeat Button

In CD mode, this button is pre pro-

grammed as “repeat” command for

ADCOM CD player.

[

] Random Button

In CD mode, this button is pre pro-

grammed as “random” command for

ADCOM CD player.

[

] Tuning Up/Down

In tuner mode, these buttons are pre

programmed to scan up or down the

GTP-860II’s AM or FM band.

[

] Pre/Tune Button

In main and tuner modes, this button

toggles between manual tuning and

preset station functions for the tuning

up and down buttons [43].

[

] RDS Button

This button selects the type of RDS

information that will be displayed

when it is available from the currently

selected radio station. The PTY mode

will indicate program material type

such as jazz or rock or classical. The

call mode will usually dispaly the call

letters of the station (WXYZ), but may

also include additional information

about the current program material.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 31 32

Kommentare zu diesen Handbüchern

Keine Kommentare

Adcom GTP-860II Bedienungsanleitung Seite 16

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Empfänger und Verstärker Adcom GTP-860II